Winter comes with the realization of blowing out pool lines, but do we really know the right way to blow out pool lines with an air compressor? Can we do it as per our own experience? No, you can’t. Knowing the right technique but before that, knowing the backend knowledge is what is needed the most to avoid any explosive or hazardous condition.
It’s a common practice among people to blow out pool lines before winter as it has its own set f advantages. It helps prevent damage to the pipes in extreme winter and much more. To tell you the right techniques and tools today, we will thoroughly talk about how to blow out pool lines with an air compressor.
This article contains all the right information based on the research done by the experts, starting from how to do the preparation to step by step guide and moving further, we have a section to give you detailed information if you are unaware of this phenomenon. So, better begin with it now:
Contents
How to blow out pool lines with an air compressor? – Step-by-Step Guide
Blowing out the lines is not particularly difficult. Really, anyone who has the appropriate tools and information can do it. Experts usually suggest using a cyclone pool blower, but yes, you can also go with any of your air compressors. An air compressor features high pressure and low/less airflow, whereas cyclones work in the opposite manner.
That being said, let’s move on to our main portion on what things you are required to blow out pool lines with an air compressor.
Things you will need:
- A connector that lets you join the compressor hose to the pool’s water lines
- Enough quantity of compressed air
Preparations before starting the operation:
Here are some of the preparations/tasks you need to do before starting the guide on how to blow out pipelines. These include:
- Depending on the type of pool cover you have, reduce the level to 4–12′′, far below the skimmer.
- Drain the water by taking off the drain plugs on the heater, pump, and filter. Put back loosely.
- The skimmer should be drained, manually pumped, or virtually completely drained of water.
A Step-by-Step Guide on How to Blow out Pool lines with Air Compressor – Quick Guide
1. Drain the pool water:
The first and foremost task is to drain the pool water completely; experts usually recommend going to a level of 10 inches for proper drainage. But still, if there is some water left, not in the form of droplets, as it will cause moisture, use a small pump to clean the skimmer.
2. Blowing air from suction:
In the second step, it is important for the ones that have the suction area, but if you have one skimmer, you can go ahead. The suction is where all the lines are attached, and you have to clean it too thoroughly.
Now you have to blow out the water from one skimmer to the pump and then repeat the process in the opposite manner, but ensure that it is plugged off to avoid any electrical current. By cleaning thoroughly, it will almost take you 2-3 minutes to dry it off.
3. Drainage of all tools:
Now, moving on, it’s time for cleaning and blowing the air out of all the attached tools that, include; the pumps, filters, etc. To do so, you need the air to flow out, so for that, remove the drain plugs, and it will dry it out.
After that, find the multi-port valve once more, and then set it to calculate accurately. At this point, your pump’s sliding valve needs to be turned so you may blow air through it to force water through.
4. Blowing out inlet lines:
In the last step, you need high pressure; that’s where air compressors main purposes are needed and do their job quite efficiently. Blow out the high pressure into all the inlet lines until you start hearing bubbling sounds, and that’s the point where you can access that now everything is cleaned and dried.
That being said, you don’t need to worry about any kind of damage. For more assurance and calculation purposes, it is advised to blow out for at least 3 minutes in each inlet line. This way, you are done with your job without taking any assistance and help just in a matter of few minutes.
Importance of blowing out pipelines
Blowing out the pipelines for winters isn’t for everybody but specifically for people living in areas/regions where the temperature falls below the freezing point. If that’s not the case for you, then mate, you don’t need to worry about it at all. But I must say, if you do this it’s pretty good for you. Also, you may be able to completely avoid this step when you own an above-ground pool by effectively removing your piping for the winter.
Your lines should be blown out to avoid any remaining water in your system freezing over the winter. This could cause damage to expensive equipment and drainage system cracking and harm.
Final words:
Damage takes place when you leave a great amount of water, and it gets frozen, as it can ultimately damage and rust the pipes or even the whole system. All you need is a portable air compressor to do the task by following the above-mentioned 4-step guide on how to effectively blow out pipelines with an air compressor.
I hope by now you got a great understanding of what you need and how to do it alongside the conditions or temperature where you can get away with it.
- How To Make A Confetti Cannon With An Air Compressor - December 4, 2022
- How To Keep Air Compressor From Freezing - December 3, 2022
- How To Install Oil Water Separator On Air Compressor - December 2, 2022
