Even though you are using a compressor for the first time, it would not make much time for you to understand how to make use of it. So, it becomes quite easy, simple, and stressless to use an air compressor once you know exactly what to do. You just have to learn some basic steps required to operate the husky air compressor.
For the first-timers who have never used an air compressor before, it is recommended to do a test run. So just simply turn off the pressure power switch. Next, plug in the power cord and start the compressor by turning it on. You would notice the pressure gauge slowly rising. After this, just turn it off, make sure to unplug the cord and then release any air in the tank.
It seems like a formality to guide the reader towards reading the manual while using an air compressor, but the thing is that it is important to familiarize yourself with your husky air compressor before using it. You would have a slight idea about all the components once you would go through the manual of your husky air compressor and the rest will be taken care of in this article.
Learn how to use a husky air compressor
Check the tire pressure and PSI
If you are unaware of the exact tire air pressure, it might not be that easy to work on it. Therefore, the first thing you need to focus on is checking how much pressure (air) the tire need. Usually, you need to be exact about the amount of air in the tire required. Otherwise, your tire will certainly not perform well and you can face many other problems as well.
Most of the vehicles require around 150 pounds of pressure for each tire. The fact is that this amount actually depends on the PSI. Plus, there are some other factors as well that influence the pressure such as the axle load, weather, and tire axle.
It is strongly recommended to check the pressure amount from the car’s manual. It is better to avoid using the number of PSI mentioned on the tire’s sidewall. Well, because, it misguides the users by presenting the maximum pressure count.
Find out the pressure needed
You must not ignore checking the design and model number of your husky air compressor. Generally, the tanks of small compressors contain up to 110 to 140 PSI. Try to know about the tire gauge as well. There is a tire gauge that indicates how much air pressure the tire need.
It is essential to understand that if one provides much air, then one might face some problems as discussed earlier. In case you set less pressure, then, there are chances of extra friction problems. Not only but, it might even raise the temperature of the rubber. and obviously, heat is very harmful to the rubber, in this case, tires. In addition, If the situation gets worst it can even damage the steel cables.
Be extra careful while filling the tires and make sure that it is cold. This way you would get a more accurate reading. Well, if you notice any sort of flat tire problems while driving, you should wait around 30 minutes. Wait for the tires to become cool and then carefully apply air pressure to them. This is what it requires to use a husky air compressor for tires.
Prepare the tire
Before you initiate using your husky air compressor, don’t forget to get your tire ready. Make sure that tires have one stem cap bolted right at the top side of the steam valve. Now just take out the cap and put the cap to one side and be cautious about misplacing it. Don’t get panic if some air leaks when the cap comes out from the valve, it’s part of the process. Also, avoid detaching the cap till one is ready to use the machine.
Switch on your husky Air Compressor
You might already know that the husky air compressor runs through electric power. So in order to run it, you need to plug in your machine. Note that the small unit has a plug of two-prong and the larger machine usually need one plug of three-prong.
You need to ensure that the outlets being used are of the accurate voltage for your machine. The results would not be good if you run your machine on any wrong circuit. Both the compressor and the circuit can be damaged.
So, you will get sound from the motor when you switch on your compressor. The sound indicates that the motor of the compressor has started to work. Well, the good thing is that husky air compressor parts have tires and hence it is very easy to change them.
After this, locate the air compressor near the tire and then attach the hose (air) to your machine and try to include a rapid coupler. Actually, this kind of fastener enables one to push air in the steam valve.
You would see a safety part on the nozzle, it ensures that your air compressor is active. Now, secure the air hose and valve stem in order to switch on your machine. Once the machine is on, check how flat your tire is and then wait till the tire becomes full. You can find out the exact count of air for the tire through one gauge with the compressor. Automatic inflators can also be used to check the correct reading of gas. This is how can use a husky air compressor for tires.
Remove the hose
In order to remove the hose, check the pressure of the tire while filling up your tire with the help of digital auto inflators. You can easily get such kind of inflator from the market. Make sure that air pressure is balanced but if you mistakenly add much air, you can simply release some air by using the gauge. Remove the machine’s air hose once the air count is appropriate. Usually, it makes a sound while removing the hose so do not get confused. Lastly, just put the cap back onto the valve.